There is a cross -shaft -directional positioning small convex ink -type convex semi -circular hole. In addition, the needle bearing of the rolling needle is also damaged in the early stage. Therefore The loss of dynamic balance, generating vibration, bearing steel bowl is also easy to damage. .20mln).

When maintaining and repairing the cross -shaft, if the bottom groove of the bearing bowl is mistaken for the positioning slot of the rotation of the bearing bowl, and the position of the fork position is stuck on the ballad on the fork on the tok.

Cross -shaft rolling needle bearing bowl is mainly due to: U -shaped bolts are tightened too tightly, exceeding the specified torque; U -shaped bolts tighten the operation method (must not tighten one nut of U -shaped bolts first, then twist the other end of the China CV Joint manufacturers other end Naruts) The contact surface of the U -shaped bolt with the cross -shaped bearing bowl is poor and the local force is broken.

In the bottom groove of the bearing bowl, the cross -axis of the cross axis will increase by 3INM (the normal cooperation is large and only allows within 0.

Regular maintenance should regularly check the technical status of the cross bearing of the cross; avoid small convex stuck in the bottom groove of the bearing bowl when repairing during repair (the current production of Motors has canceled the tank of the bearing bowl of the bearing bowl); the U -shaped bolts Tighten them according to the prescribed torque and check it frequently

امتیاز بدهید :

Correctly install, use and maintain the correct installation, rational use and recurrent maintenance of the cross axle universal coupling, which is important to ensure the performance and its extended service life.

Avoiding the long-term overloading and illegal operation of the universal coupling, otherwise it will reduce the service life. The coupling has the advantages of high load capacity, long service life, smooth operation, noise, and large axial compensation.

After the installed universal coupling belt load is loaded after a class (8h), check whether the flange bolt is loose, and tightened again according to the preservation torque, so repeating several classes until the bolts are no longer loose. The grease is 2 industrial lithium-lithium-boe (a small amount of MOS2 can be added to the spline). If there is the above phenomenon, it is repaired or replaced.

All of the above phenomena should be hungry, analyze the reasons, and maintenance.Wanxiang coupling for normal operation during maintenance period, the maintenance Wholesale CV Joint part manufacturers period is generally in half a year to one year, and the items should be checked when repairing: Cross-axis joual, bearing outer ring and short cylindrical roller

The situation is measured, and its radial gap is measured, and the contact surface has indentation, pitting, peeling, crack, etc. (1) Is there an abnormal sound; (2) whether the cross bag has axial swift; (3) whether the radial beating is normal; (4) whether the coupling bolt is loose.25 mm, the SWP type and SWC type radial gap are highly allowed in Table 1. (2) Before the fastening bolts, threads must be cleaned or cleaned, and they are tightened, and fastened by interleaving mode (not allowed with a bottom hardness gasket). 

امتیاز بدهید :

1.The intelligence points of the universal coupling will focus on two aspects, one is to find a positive, and the other is measurement. If the components of the universal coupling appear uneven thermal expansion, or if the bearing is uneven, it will make the shaft in pairs, so it is necessary to specify a Wholesale CV Joint replacement manufacturers tolerant deviation value to specification.

Why do you want to find a universal coupling for a universal coupling? What is the purpose of this? A: The universal coupling is found, mainly to make it better, and achieve a certain accuracy by looking for positive, so that the machine can operate normally, especially high-speed running machines. In this process, if you find that the universal joint uranium appears, you should be adjusted in time to measure more.

The above is the main content of the article, for reference only!The measurement order of the measuring coupling of the universal coupling is: first connect the universal coupling, and set a dedicated tool, then tu the universal coupling, the radial direction of the four positions. And axial measurements and record the measurement results.

I hope that through the introduction of these two aspects, you can make you a further understanding of the universal coupling, thus making it more familiar with it

امتیاز بدهید :

Its angle is generally within 5 to 45 degrees. BF type: standard telescopic flange universal coupling. DH type: short telescopic welded universal coupling. Therefore, let's update this opportunity, let's talk about couplings. The torque size, nature, and requirements of the buffer damping function should be considered, and if it is a high power overload transmission, the teeth type coupling is selected.

For courses, because they are related to the website product, we also need to understand and understand it so that you can better lea the products in our website and make comprehensive and specific. The choice should be made according to the high and low centrifuge size, if it is a high-speed drive shaft, a diaphragm coupling should be selected because the Axle For Vehicles balance is high, but do not use the slider coupling because of its existence Eccentricity.

. The coupling such as a metal component should be considered according to the reliability and working environment, and no lubrication is required, but if it is containing a non-metallic component, then it is temperature, light and corrosion, etc.

According to the relative displacement size and direction of the two axes, if the radial displacement is large, the slider coupling can be selected, and if it is a large angular displacement, the universal coupling should be used. The following small series will come to this guidance in order to let everyone have a reference. Sensitive, and it is also easy to appear. There are a wide variety of couplings, then we should choose to choose when selecting it

امتیاز بدهید :

If you exceed this range, then there will be problems.Universal coupling, its prominent characteristics, why? It is different in different forms on both axis angles, is it different? The outstanding characteristics of the universal coupling is mainly three, which is a compact structure, high drive efficiency, and a large angular compensation capability.

Because, use one universal joint, the speed of the left and right ends is uncomfortable, and it is fluctuating. And a universal coupling, it is not the same, so there will be this conclusion.Universion coupling, it is not only one of the website products, but also from the current point of view, its application is still very broad, so it is necessary to make its leaing work, so that everyone has clear understanding And correct understanding, and simultaneous, you can also broaden your knowledge. 20,000 and universal coupling, is it?

Universal joints and universal couplings, although the name looks almost, but both are different. Want to let the universal coupling are smoothly driven, then what should I achieve? Universion couplings, if you want to achieve smooth transmission, then you must use two universal joints, so that it can achieve the purpose.

However, in general, it is within 5 to 45 degrees. So, use a universal joint to make the speed becomes stable, thereby reaching the above objectives. So, based on this, and you have some foundations in front, you may continue, so that OEM Birfield UF CV Joint everyone will benefit from it. The angle between the two-axis between the two-axis is different from the form of different structures, so on the question 2, its answer is. Because of the universal joint, it is a universal joint, which is used to perform a variable angle power transmission, thereby changing the direction of the transmission axis

امتیاز بدهید :